NEV Charging Gun Temperature Sensor Selection Guide

Abstract: Under high-current charging conditions, the terminal contact resistance of NEV DC charging guns generates heat that causes temperature to rise rapidly. Without reliable temperature monitoring and over-temperature protection, there are risks of insulation aging, terminal ablation, and even fire. This article focuses on NTC temperature sensor selection for charging guns, providing key parameters such as R25, B-value, accuracy, and response speed, along with three-level protection thresholds at 85C, 95C, and 105C as a practical selection scheme.

ac8ad4a6 201a 40f6 ad57 062f5fb3ad61

1. Why Charging Gun Temperature Rise Cannot Be Ignored

The DC charging gun is the “last mile” of energy transfer between the charging pile and the traction battery. The rated currents specified in GB/T 20234 cover 16A, 32A, and 63A, while high-power fast-charging guns sustain currents above 200A. When such large currents flow through the terminals, even a few milliohms of contact resistance produces considerable Joule heating.

Field tests show that after 30 minutes of continuous charging at 32A, terminal temperature can rise from ambient to above 70C; under 63A conditions, terminal temperature easily exceeds 90C. Once temperature is left uncontrolled, three cascading problems arise: first, terminal plating oxidizes more rapidly and contact resistance increases further, forming a positive temperature feedback loop; second, the gun cable insulation material (typically rated for 125C) ages faster; third, in extreme cases the plastic housing softens and deforms, leading to insertion failure or even short circuits.

For this reason, GB/T 18487.1 explicitly requires charging guns to have temperature monitoring and to trigger alarms, power derating, or power cutoff when temperature exceeds limits. NTC thermistors, with their low cost, small size, and high accuracy, have become the mainstream solution for charging gun temperature monitoring.

2. NTC Temperature Sensor Selection Scheme

Charging gun NTC selection must balance three dimensions simultaneously: measurement accuracy, response speed, and long-term reliability. The table below shows the recommended parameters from Yuanlin Electronics.

ParameterRecommended ValueSelection Rationale
R25 nominal resistance10K ohmMatches the ADC voltage-dividing sampling circuit of the charging pile controller; 10K is the most common industry spec
B-value (25/85C)3950KGood sensitivity and linearity in the 85-105C operating range
Accuracy classplus or minus 1%Avoids temperature misjudgment causing false alarms or missed protection
Thermal time constant tauno more than 15sEnsures timely protection trigger when terminal temperature is abnormal
Dissipation factorat least 1.5mW/CReduces self-heating effect on measurement accuracy
Operating temperature-40C to +125CCovers outdoor environment and high-temperature terminal conditions
Packaging formEnamel wire / PVC wireEasy to mount near terminals with good insulation
Lead lengthCustom (typically 150-300mm)Accommodates the routing distance from terminal to gun-tail control board

Charging Gun Temperature Measurement Scheme (Text Description):
[Gun Head] DC+ terminal — NTC1 mounted at terminal root — lead routed along inner wall — connected to ADC sampling port on gun-tail control board
[Gun Head] DC- terminal — NTC2 mounted at terminal root — same routing path — connected to another ADC sampling port
[Control Board] Dual NTC signals through voltage-divider resistors -> MCU ADC -> software filtering -> temperature calculation -> over-temperature logic (85C alarm / 95C derating / 105C cutoff)
[Pile Level] Ambient temperature NTC + power module temperature NTC -> charging pile main controller -> evaluated together with gun temperature

For monitoring point placement, DC charging guns typically use 1-2 temperature points. A single-point scheme mounts the NTC at the root of the DC+ terminal where heating is most severe; a dual-point scheme places one NTC each at the DC+ and DC- terminals for redundant monitoring. High-power fast-charging guns, due to larger current and more uneven heating, are recommended to adopt the dual-point scheme.

3. Over-Temperature Protection Strategy: Three-Level Thresholds

Over-temperature protection should not simply cut power at one threshold, but rather respond in graded steps, balancing safety with charging continuity. The three-level protection strategy recommended by Yuanlin Electronics is as follows:

Level 1 — 85C Alarm: When terminal temperature reaches 85C, the charging pile sends a temperature alarm signal to the vehicle BMS and displays a local alarm. Charging is not interrupted at this stage, but the system enters a “watch state” and prepares for subsequent actions.

Level 2 — 95C Power Derating: If temperature continues to rise to 95C, the charging pile actively reduces output current (for example, from 32A to 16A) to decrease heat generation and let temperature fall back. This strategy avoids frequent power cutoffs that would hurt user experience.

Level 3 — 105C Power Cutoff: At 105C, output is cut off immediately and the fault state is latched, requiring manual troubleshooting before recovery. The 105C threshold maintains a safety margin relative to the insulation rating of 125C, preventing thermal runaway.

It is important to emphasize that charging gun temperature protection should not operate in isolation, but must be coordinated with the overall thermal system of the charging pile. The pile also needs an ambient temperature NTC (for power module temperature compensation) and a power module temperature NTC (monitoring IGBT or rectifier bridge heat dissipation). Together, the three form the thermal safety net of the charging pile.

4. Frequently Asked Questions

1. How many temperature monitoring points does a charging gun need?

A charging gun typically needs 1-2 temperature monitoring points. The common practice is to place one NTC on each of the DC+ and DC- terminals, or share a single sensor at the hottest terminal. For high-power DC fast-charging guns, dual-point monitoring is recommended for redundancy and safety.2. What response speed is required for a charging gun temperature sensor?

The thermal time constant of the charging gun NTC should be no more than 15 seconds, ensuring that the protection mechanism is triggered promptly when terminal temperature becomes abnormal. A slow response leads to delayed over-temperature protection, posing risks of terminal ablation or fire.3. How to choose R25 and B-value for charging gun NTC selection?

R25 of 10K is commonly used, matching the ADC sampling circuit of the charging pile controller. A B-value of 3950K is recommended for good sensitivity and linearity in the 85-105C operating range. Accuracy of plus or minus 1% is recommended to avoid false alarms or missed protection due to temperature misjudgment.4. Besides the charging gun, what temperatures does a charging pile need to monitor?

The charging pile also needs to monitor ambient temperature (for power module temperature compensation) and power module temperature (for IGBT or rectifier bridge heat dissipation). Charging gun terminal temperature, ambient temperature, and module temperature together form the thermal safety system of the charging pile.

About Yuanlin Electronics
Dongguan Yuanlin Electronics Technology Co., Ltd., established in 2007 in Chang’an Town, Dongguan, specializes in electronic protection components, providing one-stop solutions for over-voltage, over-current, and temperature detection protection. As the authorized agent of Taiwan Thinking (TKS) brand, the company offers a full range of NTC thermistors and temperature sensors, with R25 covering 10K/20K/47K/100K/200K, B-values of 3435/3950/4250/4571, and accuracy from plus or minus 1% to plus or minus 5%. Products are certified to ISO9001/IATF16949 and CQC/UL/VDE/CSA/SGS, widely used in NEVs, charging piles, energy storage, PV inverters, 3D printing, and power supplies.

Facebook
Twitter
LinkedIn
Email

Get A Quote